Home/ Products / Magnetic Wheel
Magnetic Wheels for Wall-Climbing Robots (Designed for Interference-Fit Assembly)
Magnetic Wheels for Wall-Climbing Robots (Designed for Interference-Fit Assembly)
Magnetic Wheels for Wall-Climbing Robots (Designed for Interference-Fit Assembly)
Magnetic Wheels for Wall-Climbing Robots (Designed for Interference-Fit Assembly)
Magnetic Wheels for Wall-Climbing Robots (Designed for Interference-Fit Assembly)
Magnetic Wheels for Wall-Climbing Robots (Designed for Interference-Fit Assembly)
Magnetic Wheels for Wall-Climbing Robots (Designed for Interference-Fit Assembly)
Magnetic Wheels for Wall-Climbing Robots (Designed for Interference-Fit Assembly)
Magnetic Wheels for Wall-Climbing Robots (Designed for Interference-Fit Assembly)
Magnetic Wheels for Wall-Climbing Robots (Designed for Interference-Fit Assembly)
Magnetic Wheels for Wall-Climbing Robots (Designed for Interference-Fit Assembly)

Magnetic Wheels for Wall-Climbing Robots (Designed for Interference-Fit Assembly)

Contact Us Now

FAIZEAL · CUSTOM MAGNETIC COMPONENTS · OEM AND ODM

Miniature Press-Fit Magnetic Wheel

Pressed on, not bolted. A custom miniature magnetic wheel that mounts by interference fit, with no keyway, no screws and no adhesive in the torque path — engineered for compact robotics, precision drives and miniature magnetic assemblies where every millimetre of the magnetic circuit counts.

Keyless interference-fit mounting · Custom-built to the customer drawing · Sintered NdFeB magnetic circuit in a precision-machined steel shell · Designed, pressed and verified in-house by FAIZEAL

Product Overview

This miniature magnetic wheel is a customer-specific development, not a catalogue part. The brief was deceptively simple: take a very small magnetic wheel and give it a mounting method that does not consume the space the magnetic circuit needs. Our answer was an interference-fit, press-on interface.

The wheel is located and driven entirely by controlled radial contact pressure between its precision bore and the mating shaft, so there is no key, no set screw, no clamping hub and no bonded joint.

What you see in the photograph is the finished component: a compact precision-machined metal ring with a finely knurled outer cylindrical surface, a stepped and accurately bored inner diameter, chamfered lead-in edges, and concentrically turned end faces.

The bore is the functional interface. Its size, tolerance band, roundness and surface finish are the features that determine whether the press fit holds torque for the life of the machine, and they are the features we machine last, after the magnet assembly is complete.

The result is a wheel that stays concentric to the shaft by geometry rather than by adjustment, transmits torque with true zero backlash, and leaves the full annular cross-section of steel available to carry magnetic flux. For a wheel of this diameter, that combination is not a refinement. It is the reason the part works at all.

Why the Mounting Method Decides the Design at This Scale

On a large magnetic wheel, a keyway or a bolt circle is a small compromise. On a miniature wheel it is a dominant one, because the space you remove and the flux you lose do not scale down together. Three conventional approaches fail in predictable ways, and understanding those failures explains why this part was built around a press fit.

A keyway cuts the magnetic circuit. A keyseat is a slot machined into the bore, and directly above it sits the steel yoke that returns the flux from the magnets. Cutting that slot locally thins the yoke, drives it towards saturation, and introduces a repeatable weak point in the air-gap field once per revolution.

On a small wheel the keyseat depth is a significant fraction of the whole yoke thickness, so the loss is not local — it shows up as reduced holding force and a periodic variation in the field.

Fasteners and clamping hubs consume the envelope. Screw heads, a hub flange or a retaining nut need radial and axial room. That room comes out of the magnet volume, the wheel width, or the clearance around the assembly, which is exactly what a compact robot joint or a miniature drive cannot give up. Fasteners also add mass at the radius where rotating inertia hurts most.

Adhesive has a temperature ceiling and an inspection problem. Structural adhesive is workable on large parts, but on a miniature bore the bond line is thin, hard to dispense repeatably, and impossible to inspect after assembly. Its strength falls as temperature rises, and it ages under thermal cycling. A bonded wheel can look perfect on the bench and slip in service with no warning.

The interference fit removes all three problems at once. It needs no cut in the yoke, no extra hardware, and no polymer layer. The joint is made of the same steel that already carries the flux.

The Interference Fit: How the Joint Actually Works

An interference fit is a controlled elastic interference between the wheel bore and the shaft. The shaft is made very slightly larger than the bore, so pressing the two together elastically expands the wheel and compresses the shaft. The resulting radial contact pressure generates a frictional holding force around the full circumference. The following subsections describe what that means in engineering terms for this part.

Torque transmission and axial location without a key

The frictional force at the bore surface resists both rotation and axial movement, so a single interface locates the wheel axially and transmits the drive torque. Because the contact is continuous around the full circle rather than concentrated on the flank of a key, there is no mechanical clearance and therefore true zero backlash. Torque reversal, high-frequency indexing and frequent start-stop duty produce no impact loading on a key flank, because there is no key flank.

The load is also shared uniformly. A keyed joint carries the entire torque on one small bearing area, which is where fretting and fatigue cracks begin. A press fit distributes it over the whole bore, which lowers contact stress and makes the joint tolerant of the shock loads that compact drive systems routinely see.

Self-centering concentricity from the mating surfaces

A press fit centres itself. The bore and the shaft find a common axis during the press stroke, so the wheel's outer diameter runs concentric to the shaft without shims, adjustment or a secondary machining operation. That matters directly for magnetic performance: the air gap between the wheel and the surface it acts on is constant around the circumference, so the holding force is repeatable and the field does not wobble once per revolution.

Our standard process holds outer-diameter concentricity in the 0.02–0.05 mm total indicator reading band, with roundness and cylindricity managed alongside it, and mating surfaces finished to a controlled roughness so that microscopic unevenness does not create local air-gap variation. The bore is ground to H7 or tighter to the agreed fit class before pressing.

An uninterrupted magnetic circuit

Because the bore carries no keyseat and the shell carries no bolt holes, the steel return path is a complete, unbroken annulus. Flux is not forced to detour around a slot or a drilled hole, and the magnet volume is not reduced to make room for hardware. For a given outside diameter, that means a higher usable air-gap flux density, a more uniform field distribution, and better adhesion-to-volume ratio.

This is the quiet advantage of the press fit on a miniature wheel: the mounting decision is also a magnetic-circuit decision. Choosing a keyless interface is what lets us spend the entire cross-section on flux instead of spending part of it on fixing.

Keeping the press load away from brittle magnets

Sintered NdFeB is hard, brittle and sensitive to tensile stress. An interference fit generates hoop stress in the wheel, so the design must ensure that this load is carried by the steel shell and the steel back-iron, never transmitted into the magnet array as a direct compressive or bending load. This is the single most important structural rule on the part.

We achieve it by assigning the bore to a continuous steel component with sufficient wall thickness, by locating the press contact away from the magnet seating surfaces, and by avoiding hard-on-hard contact between the fixture and any magnet surface throughout assembly. Where the design is marginal, we check the stress field with finite-element analysis before releasing the drawing, so the interference that gives the joint its grip does not become the interference that cracks a magnet.

Defining the interference window

The interference is a window, not a target. Too little and the joint slips under peak torque or thermal growth. Too much and the press force climbs, the plating is at risk of scoring, and the hoop stress approaches the yield limit of the shell. Both ends of the window are calculable from the shaft and bore materials, the engagement length, the surface finish, the operating temperature range and the required transmissible torque.

We agree the fit class with the customer at the drawing stage, then verify it against the full duty envelope: the maximum torque, the highest and lowest service temperatures, and the thermal-expansion mismatch between the wheel and the shaft or housing material.

A steel shaft in an aluminium carrier, for example, loses interference as temperature rises; a design that is correct at room temperature can become marginal in a hot enclosure. That check is part of the engineering review, not an afterthought.

Controlled Press Assembly

Pressing a magnetic assembly is not the same as pressing a plain steel bush. The following controls are applied to protect both the joint and the magnets, and they are the reason we prefer to carry out the press fit in-house as part of the delivered assembly.

l Lead-in geometry. A chamfer on the bore entry and on the shaft end guides the two parts onto a common axis and prevents the bore edge from shaving the shaft during the first millimetres of travel.

l Coaxial tooling. A guided press tool and a locating mandrel keep the load axial. Side loading during a press stroke is the classic cause of a skewed wheel and a scored bore.

l Continuous, impact-free force. The press advances at controlled speed with no hammering. Brittle magnet material must never see an impact load, and the force path runs through the steel shell only.

l Press-force and displacement monitoring. The force-versus-travel curve is recorded for every part. An anomalous curve is an immediate diagnostic: too low suggests insufficient interference, too high suggests misalignment or an out-of-tolerance shaft, and a sudden step suggests surface damage.

l Positive end stop. A mechanical stop sets the final axial position, so the wheel cannot be pressed past its designed location onto a shoulder it was not meant to contact.

l Post-press verification. The assembly is checked for axial position, runout, and holding capacity, then re-measured magnetically to confirm that pressing did not disturb the field.

Where the application calls for thermal assembly rather than a mechanical press, we can specify an induction or oven-heating procedure with a controlled temperature limit that protects both the magnet grade and the coating. The two routes are evaluated together at the design review, and the chosen method is written into the process sheet.

What We Need From Your Shaft or Housing

An interference fit is a two-part design, and the wheel is only half of it. To release a drawing that will hold in production, we ask for the following information about the mating component. Providing it at the enquiry stage is the fastest way to a reliable fit and an accurate quotation.

l Shaft or housing material and hardness, including any heat treatment or surface coating

l Nominal diameter, the specified tolerance band, and the required engagement length

l Roundness, cylindricity and surface roughness of the mating surface

l Shoulder geometry, lead-in chamfer and the axial datum that defines final position

l Peak and continuous torque, plus any torque reversal or shock loading in the duty cycle

l Operating and storage temperature range, and any wash-down, chemical or vacuum exposure

l Rotational speed and the required balancing grade, where the wheel is a rotating element

l Whether the assembly must be removable for service, and what removal access exists

With those inputs we return a proposed fit class, a calculated interference range, an estimated press-force envelope, and a stress check on the shell. If the customer's shaft is already fixed, we work to it. If it is still open, we recommend the shaft design that gives the widest safe interference window.

Verification and Quality Records

Every wheel is verified as a finished assembly, not as a set of parts. The inspection package covers the mechanical interface, the magnetic performance and the dimensional envelope, and the records travel with the shipment.

l Joint integrity. Pull-off force or slip-torque testing against the agreed acceptance value, with the press-force curve retained for each serial number.

l Magnetic performance. Air-gap flux density and surface field distribution scanned after assembly, so weak magnetisation, wrong pole count or pole-arc deviation is caught before dispatch.

l Geometry. Bore size, outer diameter, width, runout and concentricity checked by coordinate measurement, with roughness verified on the mating bore.

l Balance. Dynamic balancing available to G2.5 as standard and G1.0 on request for higher-speed rotating duty.

l Surface and coating. Plating or coating condition inspected after pressing, with salt-spray or media-resistance data supplied where the environment requires it.

Serviceability: A Straight Answer

A correctly designed interference fit is not intended to be disassembled repeatedly. Repeated pressing work-hardens and wears the mating surfaces, and each re-press reduces the available interference. We state this plainly because it affects how the surrounding machine should be designed, and it is better raised at the specification stage than discovered during maintenance.

Where field service is a requirement, we design for it rather than ignore it: an extraction feature behind the wheel, a controlled heating procedure, a sacrificial sleeve that takes the wear instead of the shaft, or a replacement wheel supplied as a matched set with its shaft. Tell us the service scenario and we will build the removal path into the design.

Key Features at a Glance

l Keyless press-fit mounting. No keyway, no set screw, no clamping hub and no adhesive in the torque path.

l True zero backlash. Continuous circumferential contact removes mechanical clearance entirely, including under torque reversal.

l Uninterrupted magnetic circuit. A complete steel annulus with no slot or bolt hole, for higher usable air-gap flux density in a miniature envelope.

l Self-centering concentricity. The bore and shaft share one axis by geometry, holding a constant air gap around the circumference.

l Uniform load distribution. Torque is shared over the full bore instead of concentrated on a single key flank.

l Stress-isolated magnet array. Press load is carried by the steel shell and back-iron, verified by finite-element analysis where the margin is tight.

l Precision stepped bore with lead-in chamfer. Machined last, after magnet assembly, so the press interface is true on the finished part.

l Controlled press process. Guided coaxial tooling, impact-free force, force-displacement monitoring and a positive end stop.

l Verified as an assembly. Slip-torque testing, flux mapping, dimensional inspection and optional dynamic balancing, with records supplied.

l Built to your drawing. Diameter, width, bore fit, magnet grade, pole pattern, coating and balancing grade are all specification variables.

Customisation Envelope

This wheel is an example of what we engineer, not a fixed size on a shelf. The table below summarises the design space available for a custom press-fit miniature magnetic wheel. Every listed item is agreed on the drawing before tooling begins.

Design variable

Options FAIZEAL engineers to your drawing

Wheel geometry

Outside diameter, width, bore diameter, shoulder and step geometry, chamfers, knurled or plain outer surface

Press interface

Agreed fit class on the bore and shaft, engagement length, surface roughness, lead-in chamfer, calculated interference window and press-force envelope

Magnet material

Sintered NdFeB across the N35–N52 range with M, H, SH, UH and EH temperature grades; SmCo, hard ferrite, AlNiCo and FeCrCo where the environment requires them

Magnetisation

Radial or axial multi-pole, Halbach array, pole count, pole-arc coefficient, skewed magnetisation for reduced cogging

Shell and hardware

Low-carbon steel, 304 or 316L stainless, Q235, aluminium alloys, brass and titanium alloys, selected for both flux path and thermal-expansion match

Surface protection

Ni-Cu-Ni triple plating, zinc, epoxy, parylene, Dacromet, or an elastomer-encapsulated sealed tread

Assembly method

Controlled mechanical press fit, or thermal assembly with a temperature limit set to protect the magnet grade and coating

Balance grade

G2.5 standard, G1.0 for higher-speed rotating duty

Verification

Slip-torque or pull-off testing, air-gap flux mapping, coordinate measurement, runout and roughness reports, salt-spray or media-resistance data

Typical Applications

Miniature wall-climbing and pipe-inspection robots. Drive and adhesion wheels in very small crawlers, where the wheel must grip a steel surface without a protruding hub and where zero backlash makes precise positioning possible.

Precision conveyance and tensioning rollers. Magnetic rollers that hold, guide or transport thin steel sheet, foil or components in compact automation equipment, with a flush bore that keeps the roller face unobstructed.

Encoder and sensor magnetic rings. Multi-pole rings pressed directly onto a shaft, where concentricity and pole-arc accuracy determine signal quality and a keyway would disturb the field once per revolution.

Compact servo and frameless motor rotors. Rotor assemblies for joint actuators and small direct-drive motors, where an unbroken yoke, low rotating inertia and a backlash-free shaft interface are all required at once.

Semiconductor, optical and laboratory equipment. Miniature magnetic drive and coupling elements in clean or vacuum environments, where adhesive outgassing and loose fasteners are unacceptable.

Medical devices and miniature actuators. Small, quiet, precisely located magnetic wheels and rotors for handheld and instrument-scale mechanisms with limited assembly space.

Why FAIZEAL

FAIZEAL is a magnet engineering and manufacturing company, not a trading company. Magnetisation, precision machining, press assembly, encapsulation and inspection are carried out in-house, and magnetic wheels, Halbach rotors and magnetic couplings are core products rather than sidelines. That matters for this part in particular: the press fit, the magnet array and the bore tolerance are one coupled system, and they have to be engineered by the same team that builds them.

We have supplied custom magnetic assemblies to robotics, new-energy and industrial customers in more than 30 countries since 2017. Our engineers work from a drawing or from a problem statement, and finite-element-based magnetic and structural assessment is part of the design review rather than a paid extra.

Request Your Custom Press-Fit Wheel

Send us your shaft drawing, the torque and speed duty, the operating temperature range and the space envelope. Our engineers will return a proposed interference-fit class, a calculated press-force and stress assessment, a recommended magnet configuration, and a quotation. Prototypes are available with fast sample turnaround, and production scales on the same tooling and inspection plan.

  Give us the shaft. We will engineer the fit that holds it.

FAIZEAL · Ningbo Fengzheng Magnetic Application Technology Co., Ltd. · fzmag.com · Custom miniature press-fit magnetic wheels · sales@fzmag.com

0
Comments
Share your thoughts   Showing 6 of 0 reviews
Leave a Comment
Your email address will not be published. Required fields are marked *
Name can't be empty
Email error!
Submit Comment

Get in Touch with Us

Name can't be empty
Email error!
Message can't be empty
Captcha Error!
Send Your Message

Related Products

Contact Us Now
Name can't be empty
Email error!
Message can't be empty
Send Message